| View previous topic :: View next topic |
| Author |
Message |
burgerbern
Joined: 21 Sep 2007
Posts: 56
|
 Posted: Sat Dec 12, 2015 7:01 am Post subject: ATSF Gators cabview |
 |
|
I just got round to setting up the ATSF Gator pack i purchased in August, unlike all the other BLW sets i have purchased this one does not show the nose of the loco when in the cabview, this is usually present in the FA for the loco but on this set there is no body in the FA so nothing to show, with their long noses it shows up quite noticably. it affects both units the 7's and 15's a pic below shows what is seen from the hi-nose RSD15 view, similarly there is no long low nose in the RSD7view
 |
|
| Back to top |
|
 |
Gaetan
Site Admin
Joined: 21 Sep 2007
Posts: 1107
Location: Mont-Joli QC
|
| Posted: Sat Dec 12, 2015 1:48 pm Post subject: |
|
|
the position of the cabview can not allow you to see the nose Bernard
i just check and add the nose with the FAnim and i don't see the nose both MSTS and OR
you can try i just reupload the patch in the patch section with new Fanim
Gaetan
_________________
Gaetan
BLW |
|
| Back to top |
|
|
burgerbern
Joined: 21 Sep 2007
Posts: 56
|
| Posted: Sat Dec 12, 2015 4:30 pm Post subject: |
|
|
Thanks for the updated FA's
after a while of trial and error i have positioning info for the hi nose RSD7 cabview, its the best positions i could find after a lot of trial and error. still have to have a go with the low nose but hoping the same values will work on that as well
here they are for OR std FOV setting of 45 (i cannot check in MSTS as the eng files are OR modified and will not run in MSTS)
SIMISA@@@@@@@@@@JINX0h0t______
Tr_CabViewFile (
CabViewType ( 2 )
CabViewFile ( ../../Common.Cab/BLW_Cab/Century_Cab/HNfront1024.ace )
CabViewWindow ( 43 0 597 412 )
CabViewWindowFile ( ../../Common.Cab/BLW_Cab/Century_CabHNfront1024.ace )
Position ( 1.3 3.5 2.1 )
Direction ( 08 -21 0 )
CabViewFile ( ../../Common.Cab/BLW_Cab/Century_Cab/Mlw630left.ace )
CabViewWindow ( 0 0 640 480 )
CabViewWindowFile ( ../../Common.Cab/BLW_Cab/Century_Cab/Mlw630left.ace )
Position ( 1.1 3.7 3.2 )
Direction ( -6 -77.35 0 )
CabViewFile ( ../../Common.Cab/BLW_Cab/Century_Cab/Mlw630Right.ace )
CabViewWindow ( 20 0 640 480 )
CabViewWindowFile ( ../../Common.Cab/BLW_Cab/Century_Cab/Mlw630Right.ace )
Position ( 1 3.4 3.79 )
Direction ( -6 60 0 )
Last edited by burgerbern on Sun Dec 13, 2015 9:36 am; edited 1 time in total |
|
| Back to top |
|
|
burgerbern
Joined: 21 Sep 2007
Posts: 56
|
| Posted: Sat Dec 12, 2015 5:27 pm Post subject: |
|
|
and this is the best config i can find for the RSD15 for OR (std FOV setting of 45), any move backwards in the cabview beyond this has a large object start to appear in the middle of the center window outside that gets bigger the further you move back, no idea what it is as nothing shows in the FA when i look at it
SIMISA@@@@@@@@@@JINX0h0t______
Tr_CabViewFile (
CabViewType ( 2 )
CabViewFile ( ../../../Common.Cab/BLW_Cab/Century_Cab/LNfront1024.ace )
CabViewWindow ( 43 0 597 412 )
CabViewWindowFile ( HNLNfront1024.ace )
Position ( 1.3 3.35 2.45 )
Direction ( 08 -21 0 )
CabViewFile ( ../../../Common.Cab/BLW_Cab/Century_Cab/Mlw630left.ace )
CabViewWindow ( 0 0 640 480 )
CabViewWindowFile ( ../../../../Common.Cab/BLW_Cab/Century_Cab/Mlw630left.ace )
Position ( 1.1 3.7 4.2 )
Direction ( -6 -77.35 0 )
CabViewFile ( ../../../Common.Cab/BLW_Cab/Century_Cab/Mlw630Right.ace )
CabViewWindow ( 20 0 640 480 )
CabViewWindowFile (../../../Common.Cab/BLW_Cab/Century_Cab/Mlw630Right.ace )
Position ( 1 3.4 3.79 )
Direction ( -6 60 0 ) |
|
| Back to top |
|
|
|
